[WHICT] Lab 4 Implementing MSTP
"What's Happen In Class Today"
Topic: Lab 4 Implementing MSTP
Log Date:
Venue: Room 3-2, E-2, Inixindo,
Presented by Andi Maulana
Reported by Arnastya I S
Legend:
[ASWx = Access Switch X; ASWy = Access Switch Y; DSWx = Distribution Switch X; DSWy = Distribution Switch Y]
Task 1: Configure Switch for Routing
Step 1: Read the instructions...
Step 2: Enter global config
ASW1#
ASW1#conf t
ASW1(config)#
Step 3: change mode mst to PVRST
ASW1(config)#spanning-tree mode rapid-pvst
Step 4: Configure DSWx
ASW1#10.1.1.1
Login:
Password:
DSW1#
Step 5: Change the IP Address of the PC from /16 to /24
Step 6: Configure the default-gateway
Read the instructions
Step 7: Change IP Address and Subnet mask of the ASWx
ASW1(config)#interface vlan 1
ASW1(config-if)#ip address 10.1.1.3 255.255.255.0
Step 8: Change default-gateway of your ASWx
ASW1(config)#ip default-gateway 10.1.1.1
Step 9: Configure interface fastethernet with “switchport access vlan” for PC
ASW1(config)#interface fastEthernet 0/3
ASW1(config-if)#swi
ASW1(config-if)#switchport access vlan 11
ASW1(config-if)#interface fa
ASW1(config-if)#interface fastEthernet 0/4
ASW1(config-if)#switchport access vlan 11
ASW1(config-if)#end
ASW1#
Step 10: Verify
ASW1#show running-config
....
Step 11: Verify PC network configurations
Step 12: Establish DSWx configurations
DSW1#
Step 13: Deleting VLAN 251 and VLAN 252
DSW1(config)#no vlan 251
DSW1(config)#no vlan 252
ASW1(config)#end
Step 14: Shutdown the link between DSW1 and DSW2
DSW1(config)#
DSW1(config)#interface fastEthernet 0/13
DSW1(config-if)#shut
DSW1(config-if)#exit
DSW1(config)#inter
DSW1(config)#interface fa
DSW1(config)#interface fastEthernet 0/14
DSW1(config-if)#shut
DSW1(config-if)#exit
DSW1(config)#interface fastEthernet 0/15
DSW1(config-if)#shut
DSW1(config-if)#exit
DSW1(config)#interface fastEthernet 0/16
DSW1(config-if)#shut
DSW1(config-if)#exit
DSW1(config)#
Step 15: Enable IP routing
DSW1(config)#ip routing
Step 16: Enter no ip classless command
DSW1(config)#no ip classless
Step 17: Enable EIGRP routing protocol
Step 18: Enter network 10.0.0.0
DSW1(config)#router eigrp 1
DSW1(config-router)#network 10.0.0.0
Step 19: Proceed Task 2
Task 2: Configure VLAN Interface for IP Addresses with Layer 3 Routing
Step 1: Configure IP Address
Step 2: Enter global config
Step 3: Enter global config
DSW1#
DSW1#conf t
DSW1(config)#interface vlan 1
DSW1(config-if)#ip address 10.1.1.1 255.255.255.0
DSW1(config)#interface vlan 11
DSW1(config-if)#ip address 10.1.11.1 255.255.255.0
DSW1(config)#interface vlan 12
DSW1(config-if)#ip address 10.1.12.1 255.255.255.0
DSW1(config)#interface vlan 13
DSW1(config-if)#ip address 10.1.13.1 255.255.255.0
DSW1(config)#interface vlan 14
DSW1(config-if)#ip address 10.1.14.1 255.255.255.0
DSW1(config-if)#end
DSW1#
Step 4: Configure VLAN1 and VLANsX1 to X4 as passive interface
DSW1(config)#router eigrp 1
DSW1(config-router)#passive-interface
Step 5: Configure interface as a routed ports and assign an IP Address for each interface to BBSx
DSW1(config)#interface fa0/9
DSW1(config-if)#no switchport
DSW1(config-if)#ip address 10.1.111.1 255.255.255.0
DSW1(config-if)#no shutdown
DSW1(config-if)#interface fa0/10
DSW1(config-if)#ip address 10.1.111.1 255.255.255.0
DSW1(config-if)#no switchport
DSW1(config-if)#no shutdown
Step 6: Verify
DSW1#show ip int brief
----text omitted---
FastEthernet0/8 unassigned YES unset down down
FastEthernet0/9 10.1.111.1 YES manual up up
FastEthernet0/10 10.1.113.1 YES manual up up
FastEthernet0/11 unassigned YES unset down down
----text omitted---
Step 7: Verify
DSW1#show running-config
----text omitted---
interface FastEthernet0/8
!
interface FastEthernet0/9
description DSW1 0/9 BBS1
no switchport
ip address 10.1.111.1 255.255.255.0
speed 100
duplex full
spanning-tree portfast
!
interface FastEthernet0/10
description DSW1 0/10 BBS2
no switchport
ip address 10.1.113.1 255.255.255.0
speed 100
duplex full
spanning-tree portfast
!
interface FastEthernet0/11
----text omitted---
Comments